Welcome to our AMC CRUSHER!

  • icon-facebook
  • icon-twitter
  • icon-google
  • icon-linkedin

cone crusher maximum feed size

  • Crushing Equipment | Superior Industries | U.S. Manufacturer

    2021-12-17 · Patriot ® Cone Crusher. Secondary, Tertiary, Quaternary. Maximum Feed Size 12 7/16″ (316mm) Product Size 5″ – minus #6 (125mm – 3mm) Maximum Reduction Ratio 6:1 Maximum Production Rate 820 STPH (745 MTPH) — Materials: Cubicle Products, Fractured Gravel, Ore/Hard Rock, Quarried Stone, Recycled Concrete, River Gravel, Super Pave

  • ZI CONE | Crushing/Grinding | EARTHTECHNICA CO., LTD.

    2021-11-4 · Note2. Maximum feed size is for the case where pit gravel is primarily or secondarily crushed. In case of cobble gravel, use the said thickness values as the standard. Note3. Actual capacity may vary due to characteristics and conditions of feed material (such as compressive strength, size distribution, etc.). Note4.

  • RC Series Cone Crusher

    Large Feed Opening. Min. wear and operating cost. Multi slender fix shaft. Lower power consumption with High output. Long crushing cavity to get the best cubic shaped product. No backing material required for linear fixing-Quick liner changes and cost-effective. For details please refer to the brochure. View Brochure.

  • QS332 Cone Crusher

    CS430 cone crusher: Maximum feed size: 14 ⅛ in. Engine: C9 / C9.3 Acert 261 kW (350 hp) Transport length: 51 ft 10 in. Transport width: 9 ft 2 ¼ in. Transport height: 12 ft 5 ½ in. Weight: 88,185 lb

  • HP series cone crushers Wear ...

    2020-4-15 · size of feed and the size of the outgoing product. It is normally measured at the 80% passing point. A typical reduction ratio in the HP standard cavity is 3-5 and in the HP short head cavity it is 2-4. Wear parts application guide - HP series cone crusher HP cone crusher and basic concepts Product Feed

  • Cone Crushers TC1150

    2021-2-1 · • Crusher hopper Metric Imperial Motor Size 225 kW 300 hp Cone Head Diameter (nominal) 1150 mm 45" Maximum Feed Size 220 mm 8.5" Maximum Closed Side Setting 45 mm 1.75" Capacity @ 1" (25 mm) CSS 220 - 260 MTPH 240 - 285 STPH Basic Crusher Weight 14,225 kg 31,360 lb Bearing Type Thrust Taper Roller Bearing Type Radial Roller

  • Crushers

    Maximum feed size. Reduction ratio must be limited to 3 (-4). Recommended max feed size is 50 mm. Correct feed distribution. Feed distribution should be non segregated and evenly distributed around crushing cavity. Setting closer to required product; Correct choke point. This means the right selection of cavities for feed in question. Crusher ...

  • Modular Plants MC380X Cone Module

    2020-12-15 · chamber selection, feed method and other site specific operating conditions. Contact your nearest ® distributor for further details. Cone Specifications Motor Size 300 hp (225 kW) Cone Head Diameter 48" (1219 mm) Maximum Feed Size 12-3/4" (325 mm) Capacity 135-560 TPH (125-505 MTPH) Basic Crusher Weight 43130 lbs (19565 kg)


    Crusher type Cone crusher, hydraulically adjusted Application Minerals processing Crushing stage Secondary Max. feed size 431 mm CSS range 22-70 mm Nominal capacity* 212-659 mtph Ambient temperature -20°C to +40°C (Contact if outside range) (Contact if outside range) * Capacity and possible CSS is dependent on the crushing

  • QH332 Tracked Hydrocone Crusher | Premier Equipment

    Key Specifications. Equipment: CH430 cone crusher Maximum Feed Size: 185 mm / 7″ Engine: C9.3B 280 kW / 375 hp; C9.3 261 kW / 350 hp Transport Length: 15.87 m / 52′ Transport Width: 2.94 m / 9′ 6″ Transport Height: 3.51m / 11′ 2″ Weight: 40,215 kg / 88,658 lbs

  • Cone Crusher Feed Size | Crusher Mills, Cone Crusher, Jaw ...

    The max.feeding size should be ≤85% of the feed opening size.Otherwise, it will cause: 1. decrease the capacity of the cone crusher Cone Crusher,Cone Crusher Manufacturer,Export Cone Crusher … Cone Crusher From China .This page is about the Cone Crusher,If you want to konw …

  • A Detailed Overview of Cone Crushers and What You …

    2020-6-3 · The material you feed into the machine must be pre-dimensioned to the crusher. Most cone crushers have a feed opening size of 5-14", so material that''s larger than the maximum size allowable will need a first stage of crushing before they can be fed into a cone crusher. Final Product Isn''t Uniform


    2017-11-2 · Concave Maximum Feed Size Maximum CSS Minimum Recommended CSS Medium coarse 220mm (8 1/2") 44mm (1 3/4") 24mm (15/16") Sand 63mm (2 1/2") 30mm (1 3/16") 13mm (1/2") CONE CHAMBER continued Independent cone oil lubrication tank with separate oil cooler Level sensor fi tted over inlet feed box maintains the optimum choke

  • GP series cone crushers Wear parts …

    The maximum feed size in GP cone is the same as closed side feed opening. Maximum feed sizes are also stated in cavity configura-tion tables later in the guide. Closed side setting (CSS) The closed side setting defines the reduction ratio in GP cone crusher and has significant bearing on product gradation, capacity and power draw. The closed ...

  • Cone Crushers | Moore Watson Ltd

    Capacity(TPH), the above specification is an estimated performance of crusher. The data in the table is for the performance of the crusher feed with the dry material with a specific gravity of 1600kg/m3 in an opened circuit operation, also assumed the feed material''s maximum size is under crusher''s maximum feed size and does not contains finer material less than CSS.

  • Cone Crushers

    maximum feed size square hole: nominal capacity in mtph with crusher running at css (mm) nominal capacity in mtph with crusher running at css (inch) 38 1.5: 42 1.7: 46 1.8: 50 2: 55 2.2: mcs 900 mcs 900: 90-110 kw 120 hp: ec ec: 240 mm …

  • Cone Crusher

    Max Feed Size : 185mm: Min Feed Size: 19mm: Power: 110 – 150 KW: Weight: 12T: Capacity 180 – 310TPH: Cone Setting 22mm – 38mm

  • Mobile Crusher

    A Detailed Overview of Cone Crushers and What You Need to ...

  • Cone Crushers HP Series Cone Crushers

    3 Maximum feed size vary from 80 to of "B" depending on machine size and material. SPECIFICATIONS Weights - Complete Crusher and Assemblies Size HP100 HP200 HP300 HP400 HP500 HP800 Crusher Complete 5 400 kg 11 900 Lbs 10 400 kg 22 960 Lbs 15 810 kg 33 490 Lbs 23 000 kg 50 600 Lbs 33 150 kg 73 000 Lbs 68 650 kg 151 200 Lbs Bowl, Bowl …

  • Portable Cone Crushers

    CRUSHER: Model: MCH 900 MCH 900: MCH 1150 MCH 1150: Maximum Feed Size Maximum Feed Size: 130 mm 5.1" 215 mm 8.5" Capacity Capacity: up to 130 mtph up to 143 stph: up to 320 mtph up to 350 stph: Motor Power Motor Power: 90 kW (50 Hz) 122 HP (50 Hz) 200 kW (50 Hz) 272 HP (50 Hz) TRANSPORT DIMENSIONS: Length Length: 11 700 mm 38'' 4'''' 13 000 …

  • Automation Advances Productivity of Cone Crushers

    2020-9-15 · Capacity 212 - 659 metric tons per hour. Max feed size: 17 inches. Automation and Connectivity System (ACS) continuously monitors and optimizes crusher performance. 24/7 access to data via My portal. Superior Industries. Patriot P500 Cone Crusher. 500HP, 59 inches diameter. Maximum feed opening 13.5 inches.

  • Premier Equipment | QH332 Mobile Hydrocone Crusher

    Maximum feed size up to 185 mm and capable of up to 220 tph on the larger bush setting; Remote camera which makes the crushing chamber visible from ground level; Optional double or single deck hanging screen for 1, 2 or 3 way split; Key Specifications. Equipment: CH430 cone crusher; Maximum Feed Size: ...

  • Difference Between Standard and Short Head Cone …

    The maximum feed size is 300 mm, and the discharge size is about 20-40 mm. The short head cone crusher can be used for tertiary or quaternary crushing (fine crushing). The maximum feed size is 120 mm, and the output size is 5-20 mm. …

  • DP Series Cone Crusher

    Large feed opening. Minimum wear and operation cost. Modern, simple, and effective design. Low power consumption with high output. Highly efficient design with maximum energy imparted for crushing. Excellent reliability due to the components produced in state-of-the-art in-house machining facility. For details please refer the brochure.


    2009-7-30 · Maximum size that can be accepted into the crusher is approximately 80% of the gape. Jaw crushers are operated to produce a size reduction ratio between 4:1 and 9:1. Gyratory crushers can produce size reduction ratios over a somewhat larger range of 3:1 to 10:1. The primary operating variable available on a crusher is the set and on jaw and ...

  • Rock Crushing Rule of Thumb

    2015-12-16 · The maximum feed size for a jaw crusher should be about 85% of the gape. Source: Arthur Taggart; The combination of a jaw crusher and a scalping grizzly will have 15% more capacity than a stand-alone jaw crusher. Source: Ron Casson; As a rule, scalping grizzlies are rarely used anymore for (large) primary crushers.

Copyright © 2021. AMC CRUSHER All rights reserved. sitemap